SELF ETCH PRIMER VINYL WASH & ACTIVATOR 2 QUART KIT AUTOBAHN AP - 8414 & 8415

Description

AP8414 Self Etching Filler Primer
This kit is for
1 Quart of AP-8414 Primer
1 Quart of AP-8415 Activator
Stir Sticks, Strainers, and Mix Cup
FOR PROFESSIONAL USE
AP8414 is a direct to metal two component self etch filler primer. Offers excellent adhesion and corrosion protection over all ferrous and aluminum substrates. Available in gallons. Mix 1:1 with activator (AP8415).
AP-8414 Vinyl Wash Primer  AP-8414 Chromate Free Self Etching Wash Primer is a two part primer that chemically protects against the corrosion process.  It is recommended for protecting bare metal, galvanized steel and aluminum.  AP-8414 provides minimal film build for maximum protection.
Recommended Substrates  Aluminum Galvanized Steel Stainless Steel Bare Metal   Products     AP-8414     Self Etching Wash Primer    AP-8415     Self Etching Wash Primer Catalyst  Application  Surface Preparation Wash the area thoroughly with soap and water to remove contaminants that solvent based cleaners cannot remove effectively.  Clean repaired area with a good grade wax and grease remover such as AS-2900 and wipe dry with a clean cloth.  Completely sand surface with 180–220 grit sandpaper or equivalent and re-clean with wax and grease remover.  If metal surface is badly pitted or rusted, remove rust and treat with a quality metal cleaner or conditioner.  Apply AP-8414 immediately after cleaning.  Mixing Directions    1 Part AP-8414     Self Etching Wash Primer    1 Part AP-8415     Self Etching Wash Primer Catalyst    10% 893 (Optional)    Lacquer Thinner   Application Apply 1 medium wet coat only.  Use 35–45 psi at the gun or 5 to 9 psi at the cap when using an HVLP gun.  The surface should have a smooth and uniform semi-transparent finish.  Allow AP-8414 to dry 30 minutes before recoating with additional primers.  Do not apply more that one coat of AP-8414.  Do not apply over body filler or lacquer based products.  Do not directly topcoat with basecoat or single stage systems.  Always apply a primer coat before top coating.  Drying Schedule Dry times are based on recommended film thickness and are dependent on ambient temperature.      Air Dry @ 77ºF        Flash Time   2 - 3  min      To Topcoat   30 min – 45 min
Pot Life 24 hours at 77ºF  Accelerator Do not use accelerator in this product.
Fish Eye Eliminator Do not use fish eye eliminator in this product.
Repairing & Recoating AP-8414 may be recoated with additional primers or sealers after a 30-45 minute dry at 77ºF or after a minimum 1 hour cool down after force drying at 140ºF for 30 minutes.
After 4 hours AP-8414 must be scuff sanded before recoating.
Technical Data   Weight Solids
Mixing Ratio,     1:1     Package    34.6%        Ready to Spray   17.3%                        Viscosity @ Gun   20-40 #2 Zahn Volume Solids       Recommended Film Thickness  .5 to 1.5 mil    Package    8.6%   Flash Point    72ºFTCC                Coverage @ 1 mil   155 sq ft/gal  VOC @ Gun    4.83 lbs/gal  Air Pressure @ Gun   35-45 psi
Pictures are close to the paint color.
All Kits are Shipped by UPS Ground only in UPS Approved Boxes.
For Questions Call
Store 4176324894
Store Hours ~ Monday - Friday 8:00 to 5:00 CST
I have been using, and selling this paint for over 20 years.
Made in USA, in Missouri.
Ship to the lower 48 states ONLY!!!!
This Paint can be Clear Coated if you like the Clear Coat Finish.
Do to Health Risk, an approved spray mask should be used.